A coaxial cable used to bring electronic signals to a television or other electronic device terminates in an F connector. Despite the name, F connectors are round metal barrel-like bits that attach to the end of the coaxial cable. There are several ways these F connectors can be attached to coaxial cable. Professional installers use a coaxial cable stripper, which strips all three layers of the cable at once.
Then, they slip on the F connector and secure it with a coaxial cable tool, which presses the connector onto the cable and crimps it at the same time. An F connector is a fitting that connects a coaxial cable to an electronic device or a wall jack. It contains threads that allow you to screw the cable onto a TV, cable wall outlet, or other electronic devices. If you're not a pro, you probably don't have these special tools. But you might own or can borrow a basic cable crimper that will allow you to install a crimp-type F connector.
Don't have a crimper? No problem—simply buy a twist-on F connector, which you can install by hand. As for stripping the cable before adding the connector, an ordinary utility knife will do the trick. It helps to have standard electrical wire strippers for one of the steps, but you can also get by with the utility knife. Just be sure to work cautiously to protect the inner copper cable—and your fingers. Carefully make a shallow cut all the way around the cable, cutting through the outer jacket only.
Use your fingernails to peel away the jacket from the cable. This exposes the layer of fine metal shielding wires and foil just inside the jacket. The metal shielding wires inside the outer sheath of a coaxial cable are very fine and have pointy tips. This means they can easily stab a finger, so be extra cautious working with them.
Using gloves will make the job much harder to complete, so go for an ounce of prevention here. Be very careful not to cut or nick the copper wire itself, as this can affect the cable's performance. This stage depends on which type of connector you are using:.
Crimp-type F connector: Fit the crimp ring of the F connector over the end of the cable and slide it down over the outer jacket and shielding wires. Slide it until the white plastic layer makes contact with the hole inside the connector. Continue to the final step. For twist-on connectors, your work is done.
On a crimp-type F connector, place the crimping tool jaws over the crimp ring of the F connector, and squeeze the tool handles to secure the connector to the cable.
Check around the connector for any wires coming out. If you see any, use a wire cutter and trim them away. Method 3. Place the connector base over the wire. Most right-angle connectors have a base piece that holds the housing together. Some right-angle connector kits are different. Follow the procedure on whichever product you use.
Loosen the screw inside the connector. The front portion of the connector housing has an internal screw that carries the signal. Turn the screw counterclockwise to loosen it. Just loosen it. Touch the conductor to the screw and tighten it. Insert the cable into the housing so the conductor touches the screw. Hold it in place and turn the screw clockwise to tighten it. Form a snug connection so the cable stays in place. Install the back housing of the connector. Take the back portion and line it up with the notches on the front.
Then press the 2 pieces together with the cable in between them. Twist the connector base around the connector. The base locks the two sections together. Push it up until it reaches the connector, then twist it over the two pieces. Make sure the connection is snug, then the job is complete.
Yes, but the thin twin cable probably isn't as good as even a normal TV cable. Still, it's likely to work well enough, unless your signals are exceptionally poor. Yes No. Not Helpful 6 Helpful 9. Although the thin twin cable probably isn't as good as even normal TV cable, it's likely to work well enough, unless your signals are exceptionally poor.
Not Helpful 4 Helpful 6. Yes, negatively, though seldom significantly. It's always better to use a cable of the correct length than to join shorter ones together. Not Helpful 0 Helpful 2. Not Helpful 1 Helpful 2. You cannot short circuit the feeds from two providers together i. However, you can have two sockets on the same mounting plate, which is the same electrically as having two separate sockets -- one for each provider. Not Helpful 0 Helpful 1.
If a junction box doesn't get you what you want, search for "splitter box" instead. To be honest, though, most times, you could use chop-blocks and get away with it.
Not Helpful 2 Helpful 0. Include your email address to get a message when this question is answered. If you have high speed internet and more than two TV's, make sure you use a high quality RG 6-type connector. Helpful 2 Not Helpful 0. Screw-on style F connectors usually provide a weaker connection, and signal can bleed out of the cable.
Crimp-style connectors are better for a strong signal. Helpful 0 Not Helpful 0. Submit a Tip All tip submissions are carefully reviewed before being published. You Might Also Like How to. How to. More References 6. About This Article. Co-authored by:. Co-authors: Updated: May 6, Categories: Connecting Devices to Television Sets. Deutsch: Ein Koaxial Kabel anschliessen. Italiano: Collegare i Connettori del Cavo Coassiale. Thanks to all authors for creating a page that has been read 1,, times.
From start to finish it enabled me, a woman in her 70's, to change the whole set of of my digi box and TV over to a double connection to watch one station and record another without the wires falling out of the digi box. More reader stories Hide reader stories. Is this article up to date? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy.
Tora Stone May 19, Bill Shimp, Jr. Jun 17, Also, the pictures helped tremendously! Gordon Plaskett Sep 12, Tim Day Nov 6, Share yours! More success stories Hide success stories.
Featured Articles How to. Trending Articles How to. New Pages How to. Watch Articles How to.
0コメント